HAI UNA DOMANDA?

Contattaci

HAI UN'ALTRA DOMANDA?

Inviaci un'e-mail e faremo del nostro meglio per aiutarti.

Inviaci un'e-mail

Domande Frequenti

Consiglia selezionare un prodotto.

FAQ - How Do I setup Bi-wiring and Bi-amping Speaker Output Connection

Technical Service Bulletin

August 13, 2024 

There are several different speaker connecting methods to an amplifier or AV receivers, the choice of these methods can impact the sound quality and performance.

Bi-wiring and Bi-amping are the most common methods that both of them involve using separate cables for the high and low-frequency drivers of a pair of speakers.

Bi-Wiring

Bi-wiring only requires a single one audio amplifier channel, instead of using a single pair of wires to connect the amplifier to the speaker’s crossover, Bi-wiring would separate the audio signal into two separate frequencies bands and sends them through separate sets of wires, each set of wires can handle a narrow frequency to improve the sound quality (i.e., accurate and clear), but... it’s not necessarily a guaranteed way to improve sound quality.

Below is an example of Bi-Wiring speaker output connection to 1 unit of RB-1590 stereo power amplifier

Bi-Amping

Whereas Bi-amping requires two separate audio amplifier channels that with each channel dedicated to a specific frequency range of the speaker, by using a separate audio channel for each frequency range, Bi-amping is designed to provide more power and precise control to improve the sound quality (i.e., dynamic range) and reduce inter-modulation distortion. 

This method can also allow for better speaker matching, as each channel can be specifically chosen to match the frequency range of the driver it is powering.

Below is an example of Bi-Amping speaker output connection to 2 units of RB-1590 stereo power amplifier

In general, it would be worth experimenting with both above two methods to see which one provides the best sound quality for listener's particular setup with specified audio equipment.

FAQ - Rotel CD Player Abruptly Stopping Improvement

Technical Service Bulletin

July 25, 2024

CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000 

In above Rotel CD players, an annoying abruptly stopping issue has been identified in earlier developed software versions.

A rare but possible issue may occur if laser pick-up reads and reports wrong data during playback on some specified discs.  If the error occurs the correction system could cause the CD player to mistakenly abort and stop the playback status. 

This issue has been resolved in the latest released main software versions as listed below.  New production starting with the serial numbers in the list already have the updated software installed at the time of production.  Should you require this update in a CD player please contact an authorized Rotel dealer or authorized Service Center.  

Affected unit models include: CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000

Modelli Applicabili:
CD11 Tribute | CD11MKII | CD14MKII | DT-6000 | RCD-1572MKII

FAQ - Rotel CD Player Random Order Algorithm Optimization

Technical Service Bulletin

July 25, 2024

CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000

In above Rotel CD players, a random order algorithm issue has been identified in earlier developed software versions.

When the system completes the TOC reading and is ready to play, pushing the [RANDOM] button on IR remote enables random playback mode. The begins playback starting on the 1st track of CD album every time as below and not the first track in the random list.

Original Random Playback Order

Corrected Random Playback Order

This issue has been resolved in the latest released main software versions as listed below.  New production starting with the serial numbers in the list already have the updated software installed at the time of production.  Should you require this update in a CD player please contact an authorized Rotel dealer or authorized Service Center.  

Affected unit models include: CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000

Modelli Applicabili:
CD11 Tribute | CD11MKII | CD14MKII | DT-6000 | RCD-1572MKII

FAQ - Rotel CD Player Repeat Endlessly Last Track Improvement

Technical Service Bulletin

July 25, 2024

CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000 

In above Rotel CD players, an annoying repeat endlessly last track issue has been found in earlier developed software versions.

The issue occurs after pressing the [<<] reverse search button on the remote during playback and allowing the unit to backward searches for a few seconds the restore normal playback When the device reaches the end of the CD album the system mistakenly repeats the last track endlessly instead of stopping playback.

This issue has been resolved in the latest released main software versions as listed below.  New production starting with the serial numbers in the list already have the updated software installed at the time of production.  Should you require this update in a CD player please contact an authorized Rotel dealer or authorized Service Center.  

Affected unit models include: CD11, CD11 Tribute, CD11MKII, CD14, CD14MKII, RCD-1572, RCD-1572MKII, DT-6000

Modelli Applicabili:
CD11 Tribute | CD11MKII | CD14MKII | DT-6000 | RCD-1572MKII

FAQ’s -Rotel Wired IR Connection Function and Requirements

Most of Rotel products provide one 3.5mm mini-jack to receive command codes from industry-standard infrared receivers via hard-wired connections. This feature could prove useful when the unit is installed in a cabinet and the front-panel sensor is blocked.

Q: Where is the 3.5mm mini-jack on the unit?

The 3.5mm mini-jack is located on the EXT REM port of the rear panel.

Q: What’s the IR protocol used for Rotel products?

Most current Rotel products use NEC Hex codes as their standard IR library, the base hex library used for most receivers, preamps and integrated amps is NEC 8311, and current Rotel CD players is NEC 8312.

Q: What’s the NEC Protocol?

The NEC IR transmission protocol uses pulse distance encoding of the message bits. Each pulse burst is 560µs in length, at a carrier frequency of 38k Hz. A logical "1" takes 2.25ms to transmit, while a logical "0" is only 1.12ms.

Q: What’s the carrier frequency of the external IR receiver can be used for Rotel products?

Carrier frequency of external IR receiver that works with 38k Hz.

Q: How to connect the Rotel External IR Remote Control?

For standard Rotel products with IR Remote Input require power to the IR Receiver then convert the wireless IR signal to a wired data stream connected to the IR Remote Input on the device. 

Below picture shows that External remote connection needs Power Adapter, Connecting Block (IR remote transceiver), IR Receiver (3 pins for power, ground and receiving IR) and one piece of 3.5 mm Plug Shield Cord.

Q: How to choose a Plug Shield Cord?

A 3.5 mm Plug Shield Cord 2-pin or 3-pin cable is required for connection to the Rotel unit for external IR remote connection.

How do I configure Rotel to operate with Roon?

For best performance and the highest streaming quality set the Rotel unit to use USB Audio Class 2.0 from the front setup menu.  This will require installation of the Rotel USB driver on Windows based computers (no driver required for Mac) and a reboot of the computer and power cycle of the Rotel device.

You can find more information about installing the Rotel USB driver on this page: Rotel USB Drivers

Come funziona Home Theater Bypass?

La funzione Pass-through consente di trasferire il segnale audio da un ricevitore o processore surround a un preamplificatore stereo separato, senza apportare alcuna modifica al segnale. Si tratta di una funzione utile in presenza di un sistema a due canali di alta qualità con il quale si desidera occasionalmente guardare anche video con audio surround.

Per utilizzare la modalità Bypass su RC-1580, collegare l’uscita frontale del canale del processore del suono surround agli ingressi Tape 2. Dopo aver selezionato l’ingresso Tape 2, il segnale proveniente dal processore verrà inviato direttamente al preamplificatore ignorando le funzioni dei toni e del volume. Quando l’unità si trova in modalità Bypass l’indicatore BYPASS del pannello frontale sarà acceso.

Questo tipo di impostazione del sistema è un modo per integrare un amplificatore stereo da utilizzare come canale frontale di un sistema di suono surround. La funzione Bypass è disponibile solo per l’ingresso Tape 2. Non richiede ulteriori impostazioni e ciò facilita il passaggio dalla modalità stereo normale a quella surround agendo unicamente sul selettore di ingresso.

Modelli Applicabili:
RC-1580

How much does Roon cost?

For information on Roon pricing please visit www.roonlabs.com.

Michi Bluetooth 5.1 aptX™ HD Module

Technical Service Bulletin

June 16, 2023 

Michi Bluetooth 5.1 aptX™ HD Module 

The latest Apple iOS version (including OS V15.7.2) may cause the APPLE MUSIC app to stop playing audio when manually jumping between tracks in a playlist.  The Bluetooth connection is maintained but there is no audio output and no playback information (sample frequency and/or bit rate) displayed.  A hard power cycle of the unit remedies this issue. 

Earlier versions of iOS do not appear to have the same issue.  Other iOS Apps (i.e. iTunes, Spotify, Tidal, etc.) are NOT affected by this use case.

If this is reported, please contact Rotel at sales@rotelglobal.com to order a new Bluetooth 5.1 module (Rotel Part Number: 093E-BTM0002-D-3) with updated firmware V1.04 (or newer) that resolves this iOS compatibility issue.  

Note: All new delivered spare parts will be programmed by new firmware V1.04 (or newer) before package and shipment from now on, either of below two methods can help to identify this change.

1. Check and ensure a printed label with text "V1.04" being pasted on plastic package.
   
2. Or check and ensure the last 5 digits on the pasted BT ADDRESS label are higher than "28780".
   

Bluetooth module replacement requires removal of the top cover and replacing the Bluetooth module in the socket (no special tools or soldering is required) as shown below.

Affected unit models include: X3, X5, P5, X3 Series 2, X5, Series 2, P5 Series 2

Release Type

MaintenanceMajor Critical 

X3 Series 2

Software Information
Main Version V2.00
Serial Number (Change will be effective in units after the serial numbers listed below.)
Black        283-314-1050

X5 Series 2

Software Information
Main Version V2.02
Serial Number (Change will be effective in units after the serial numbers listed below.)
Black         284-315-1050

P5 Series 2

Software Information
Main Version V2.00
Serial Number (Change will be effective in units after the serial numbers listed below.)
Black        282-310-1050
 
Release Notes
● Part Number of New Bluetooth Module 5.1 is 093E-BTM0002-D-3
● New Bluetooth module 5.1 built Qualcomm IC as below photo.
The Instruction use Michi X5 Bluetooth Dongle Replacement as example
b. Remove the Bluetooth 5.1 dongle from the socket. 
c. Prepare the new ordered Bluetooth dongle (with firmware V1.04 or higher installed)
     
d. Install the new Bluetooth 5.1 dongle in the socket. Pay CAREFUL attention to pin alignment to avoid damage to the dongle and the unit.
e. Reassembly the unit and top cover.
f. Test to verify the new Bluetooth module works properly.

 

PDF file download please click below:

Technical Service Bulletin - Michi Bluetooth 5.1 aptX™ HD Module

 
Modelli Applicabili:
P5 Series 2 | X3 Series 2 | X5 Series 2 | X3 | X5 | P5

Rotel Newsletter

Please provide us with your email address to get the latest news in sound technology and products. Sign up for the Rotel Newsletter today!

关注我们

扫一扫以下二维码或者搜索微信公众号即可关注,获取最新鲜的ROTEL资讯!

微信公众号:rotel-hifi

Rotel WeChat